Page 212 - EPR Catalog 2015

CP-D range
Technical data

Data at Ta = 25 °C, Uin = 230 V AC and rated values, unless otherwise indicated

Type CP-D 24/0.42 CP-D 24/1.3 CP-D 24/2.5 CP-D 24/4.2
Input circuit - supply circuit
Rated input voltage Uin L, N
Input voltage range
Frequency range AC 100-240 V AC

3 Typical input current / 90-264 V AC /120-375 V DC
typical power consumption
47-63 Hz
Inrush current limiting
Power failure buffering time at 110 V AC 184 mA / 11.62 W 600 mA / 37.92 W 1120 mA / 69.3 W 1800 mA / 117.3 W
Internal input fuse
at 230 V AC 120.6 mA / 12 W 344 mA / 38.16 W 660 mA / 70.1 W 900 mA / 114.4 W
Power factor correction (PFC)
at 230 V AC 30 A (max. 3 ms) 50 A (max. 3 ms) 60 A (max. 3 ms)

min. 30 ms min. 60 ms

1 A slow-acting 2 A slow-acting / 3.15 A slow-acting
/ 250 V AC
/ 250 V AC 250 V AC

no

Indication of operational states DC ON: green LED V: output voltage applied
Output voltage DC LOW: red LED V: output voltage too low

Output circuit +, - ++, --
Rated output voltage
24 V DC

Tolerance of the output voltage ±1 %

Adjustment range of the output voltage - 24-28 V DC

Rated output power 10 W 30 W 60 W 100 W

Rated output current Ir Ta ͨ 60 °C: 0.42 A Ta ͨ 60 °C: 1.3 A Ta ͨ 55 °C: 2.5 A Ta ͨ 60 °C: 4.2 A
60 °C < Ta ͨ 70 °C: 55 °C < Ta ͨ 70 °C: 60 °C < Ta ͨ 70 °C:
Derating of the output current 60 °C < Ta ͨ 70 °C: 2.5 %/°C 2.5 %/°C 2.5 %/°C
2.5 %/°C

Maximum load change statical max. 1 %

deviation change of output voltage within the input voltage range max. 1 %
with

Control time < 1 ms

Starting time after applying the supply voltage at Ir 1000 ms
Rise time at rated load typ. 1 ms

Residual ripple and switching peaks BW = 20 MHz 50 mV

Parallel connection yes, using CP-D RU

Series connection yes, to increase voltage

Resistance to reverse feed 35 V / 1 s

Output circuit - No-load, overload and short-circuit behaviour U/I characteristic curve
Characteristic curve of output
Short-circuit protection continuous short-circuit stability
Short-circuit behaviour
Current limiting at short circuit continuation with output power limiting
Overload protection
Overvoltage protection typ. 0.78 A typ. 4.2 A typ. 6.05 A typ. 11.5 A
No-load protection
Starting of capacitive loads output power limiting

30-33 V DC

continuous no-load stability

unlimited

General data typ. 80 % typ. 83 % typ. 86 % typ. 89 %
Efficiency
Duty time 100 %
Dimensions (W x H x D)
18 x 91 x 57.5 mm 53 x 91 x 57.5 mm 71 x 91 x 57.5 mm 89.9 x 91 x 57,5 mm
Weight (0.71 x 3.58 x (2.09 x 3.58 x (2.80 x 3.58 x (3.54 x 3.58 x
Material of housing 2.26 in) 2.26 in) 2.26 in) 2.26 in)
Mounting 0.066 kg (0.13 lb) 0.196 kg (0.41 lb) 0.252 kg (0.55 lb) 0.386 kg / (0.72 lb)
Mounting position
Minimum distance to other units plastic
Degree of protection
Protection class DIN rail (IEC/EN 60715), snap-on mounting without any tool

horizontal

horizontal / vertical 25 mm / 25 mm (0.98 in / 0.98 in)

housing / terminals IP20 / IP20

II

3/13 ABB | Catalog Electronic Products and Relays 2015 | 2CDC 110 004 C0210